TO APPLY LARGE DECO-MAGS, lay DECO-MAGS on a clean, flat, non-metallic surface, design side up.
INSTRUCTIONS
&
HOW TO USE
&
HOW TO USE
 |  |  |  |  |  |  |
WATCH OUT!
Do not run fingers along edges of DECO-MAGS.
Children should not cut DECO-MAGS.
** Some stainless steel surfaces do not hold magnets
DECO-MAGS are easily cut with an ordinary pair of scissors or razor knife.
IT'S EASY!
1) measure (2) cut (3) apply
1) measure (2) cut (3) apply
Measure metal surface to be covered Cut and apply.
| Do not eat DECO-MAGS Do not throw DECO-MAGS Do not sleep with DECO-MAGS Do not wrap babies in DECO-MAGS and DO NOT FEED DECO-MAGS TO YOUR PETS! Thank you for your cooperation |
DECO-MAGS are a decorative product, intended for application on metal surfaces only
Do NOT place DECO-MAGS in the direct sun or on hot surfaces
DECO-MAGS are easily cleaned up with a damp sponge. Don't use harsh chemicals on DECO-MAGS
One person should hold the top of the magnet and the other to guide the magnet into place.
Some appliances and metal furniture have emblems and hardware that prevent DECO-MAGS from laying flat. Sometimes there are areas that
need to be cut out like water and ice dispensers. Measure the area that needs to be cut out or carefully make a pattern with a piece of tracing
paper. Mark the area to be cut out on the back of the magnet (the dark side) with a pencil. Carefully cut the area out with a razor knife.
need to be cut out like water and ice dispensers. Measure the area that needs to be cut out or carefully make a pattern with a piece of tracing
paper. Mark the area to be cut out on the back of the magnet (the dark side) with a pencil. Carefully cut the area out with a razor knife.
DECO-MAGS will "stick" to walls that are painted with MAGNETIC PAINT! You Tube Video:
http://www.youtube.com/watch?v=ZPigG7v2gFE
http://www.youtube.com/watch?v=ZPigG7v2gFE
MADE IN USA
COPYRIGHT 2011
three coats of a brand I bought at my home center and it was strong enough to hold the large magnets!)
IF DECO-MAGS DON'T STRAIGHTEN OUT OR HAVE A BUBBLE UNDER LARGE MAGNET SURFACE OR YOU WANT THEM PLACED ON A
CURVED APPLIANCE
EDGES OF APPLIANCES OR GET RID OF POTENTIAL BUBBLES WHEN APPLIED TO LARGE SURFACES! IT REALLY WORKS!
*CAUTION! When heating magnets with a dryer, they can get hot. Use medium/low heat and don't over-heat the magnets.
CURVED APPLIANCE
EDGES OF APPLIANCES OR GET RID OF POTENTIAL BUBBLES WHEN APPLIED TO LARGE SURFACES! IT REALLY WORKS!
*CAUTION! When heating magnets with a dryer, they can get hot. Use medium/low heat and don't over-heat the magnets.
If you use DECO-MAGS correctly and carefully, you can add our magnetic surface to an appliance that looks like you spent hundreds of
dollars on an expensive panel kit. Use rulers and make patterns with plain paper or tracing paper (if necessary) to cut out areas for
hardware, emblems or an ice/water dispenser.
dollars on an expensive panel kit. Use rulers and make patterns with plain paper or tracing paper (if necessary) to cut out areas for
hardware, emblems or an ice/water dispenser.
1. Heat it with a blow dryer. It might stick then.
2. For example, if the strip that goes along the side of the ice maker to cover it is not staying on, you might need to use a simple piece of clear tape to discreetly keep it in
place. The smaller the strip is, the easier it is to secure. Consider cutting it in half then taping in place. Thanks for your patience...this happens occasionally.
2. For example, if the strip that goes along the side of the ice maker to cover it is not staying on, you might need to use a simple piece of clear tape to discreetly keep it in
place. The smaller the strip is, the easier it is to secure. Consider cutting it in half then taping in place. Thanks for your patience...this happens occasionally.
| Use the design on the front of DECO-MAGS for precision cutting. |